brewery reference: jbb1004

MASH KETTLE

Double walled with inner shell of stainless steel (1.4301 IIIc), welds ground with grain size 220. Outer sheath made of stainless steel.

Isolation of the cylindrical part and the bottom 50 – 100mm halogen free mineral wool.

2 steam heated heating zones (bottom and cylindrical part)

Agitator and shaft in stainless steel (1.4301). Installation bottom centre. Drive via gear motor, speed controllable by frequency converter.

  • 1 x spray ball
  • 1 x manhole with glass
  • 1 x pressure relief valve – safety valve
  • 1 x level measurement

Designed for non-pressure operation

LAUTER TUN

Double walled with inner shell of stainless steel (1.4301 IIIc), welds ground with grain size 220. Outer sheath made of stainless steel.

Isolation of the cylindrical part and the bottom –  100mm halogen free mineral wool.

Bottom of lauter tun with outlet valves, back wash valves and drain valve.

Multipart sieve plate (1.4301) removable through manhole.

Hoeing (1.4301) two armed with knives and trebern sword. Installation bottom centre.

  • 1 x lauter station with CIP spray ball
  • 1 x manhole with glass
  • 1 x spray ball
  • 1 x trebern flap on cylindrical part and trebern conveyor (straight line to the bunker with max 10m distance)

Designed for non-pressure operation

MASH COLLECTOR

Double walled with inner shell of stainless steel (1.4301 IIIc), welds ground with grain size 220. Outer sheath made of stainless steel.

Isolation of the cylindrical part and the bottom 50 – 100mm halogen free mineral wool.

  • 1 x spray ball
  • 1 x manhole with glass
  • 1 x pressure relief valve – safety valve
  • 1 x level measurement

Designed for non-pressure operation

WORT KETTLE

Double walled with inner shell of stainless steel (1.4301 IIIc), welds ground with grain size 220. Outer sheath made of stainless steel.

Isolation of the cylindrical part and the bottom 50 – 100mm halogen free mineral wool.

2 steam heated heating zones (bottom and cylindrical part)

Agitator and shaft in stainless steel (1.4301). Installation bottom centre. Drive via gear motor, speed controllable by frequency converter.

  • 1 x spray ball
  • 1 x manhole with glass
  • 1 x pressure relief valve – safety valve
  • 1 x level measurement
  • 1 x economic pan dust condensator including the pad dust cooler and  blower.

Designed for non-pressure operation.

This package includes all valves, check valves, butterfly valves, 2 pumps and temperature probes. Landing and stairs made of stainless steel square roof bars, covered with corrugated sheet metal, height adjustable feet with domes.

The pan dust will be cooled down with cold water and the condensate with be transferred to the drain.

WHIRLPOOL – 65HL

Vessel made of stainless steel (1.4301 IIIc), welds ground with grain size 220. Not insulated.

  • 1 x whirlpool pump
  • 2 x lateral outlets with hand valves
  • 1 x floor drain with hand valve
  • 1 x tangential inlet port with threaded connector
  • 1 x spray ball
  • 1 x manhole
  • 1 x safety valve

Designed for non-pressure operation.

WORT COOLING AND WORT AERATION

To cool the wort a plate cooler is provided. The wort is 98ºC and is cooled to 5ºC. After cooling the wort will be aerated. The aeration is equipped with a sterile filter, flow measurement for the air, steam valve for sterilization and a hand valve.

  • 1. Section: 65hl wort is cooled with cold water from 98ºC to 17ºC in 60 minutes. (Cold water from client side must be max. 15ºC or less)
  • 2. Section: with ice water or glycol the wort is cooled to 5ºC.

CONTROL SYSTEM

Each pneumatic controlled valve will have a switch button on a control panel in the middle of the brewhouse. The temperature of the mash kettle will be controlled via the control panel with a hardware controller.

HOT WATER TANK 100HL

Vertical design.

Double walled with inner shell of stainless steel (1.4301 IIIc), welds ground with grain size 220. Outer sheath made of stainless steel.

  • 1 x hot water pump
  • 1 x circulation pump
  • 1 x Pt100 controller
  • 1 x steam valve and condensate valve
  • 1 x level measurement

Jabebo B.V.

Kokerjuffer 41 • 7559 DM Hengelo The Netherlands

T + 31 6 52 86 88 40 • bob@jabebo.nl

KVK 61407925 • VAT NL854329584B01

Cookieverklaring | Privacyverklaring